Crojfe

Search

Mergl Václav, PhD

Power Curve Determination and Electrification of Powertrain System of Harvester Crane Swinging

volume: 45, issue: 2

The work deals with the determination of the power curve for driving the swinging of the hydraulic crane of the harvester and the subsequent replacement of the hydraulic motor with an electric motor for the possibility of recuperating braking energy. For this purpose, the hydraulic circuit of the crane slewing gear was measured with flowmeters during its rotation between the angles –105° to +105°, –90° to +90° and –36° to +22°. The power was calculated from the measured values. The maximum power needed to swing the harvester crane was 9720 W. With this power, the torque reached 187.98 Nm. The average value of the power needed to swing the hydraulic crane was only 2472 W at a torque of 47.81 Nm. From these values, a synchronous electric motor with permanent magnets with a nominal speed of 2000 rpm (rotation per minute) and a power of 3246 W emerged as suitable for replacing the hydraulic motor. The use of an electric motor would, however, require a planetary gearbox with fast input speeds that would then be reduced to slow output speeds. The research results demonstrated the possibility of using an electric motor to swing the hydraulic crane during the work cycle of the harvester for the use of energy recovery from crane braking and thus the possibility of reducing fuel consumption and emissions.

Evaluating an Electric Battery for Energy Storage in a Parallel Hybrid Thinning Harvester

volume: issue, issue:

This research assesses the feasibility of employing an electric battery as an energy storage medium in the parallel hybrid powertrain of a thinning harvester, proposing it as a more economical substitute for traditional supercapacitors. An AH6 thinning harvester incorporating a battery-hybrid system was observed during felling tasks across three combustion engine speeds: 1700 rpm, 1800 rpm, and 1900 rpm. These three modes were selected in an effort to get as close as possible to the optimal RPM of 1500. Battery energy accumulation rose by 0.06 kWh at both 1700 rpm and 1800 rpm; in contrast, it declined by 0.002 kWh at 1900 rpm. Multi-criteria evaluation of felling regimes substantiated the electric battery viability as an energy storage option for thinning harvesters. Peak efficacy emerged at reduced engine speeds, coinciding with the maximum torque output of the combustion engine. These outcomes bear substantial relevance for curbing emissions and operational expenses in thinning forestry practices.

Forestry Machinery Ergonomic Assessment: A Case Study on Ecotrac Cable Skidders

volume: issue, issue:

Skidders used in forest operations are regarded as specialized machines optimized for effective and safe wood skidding across rugged terrain. Their dimensions, design, and various technical attributes are primarily influenced by practical considerations, such as productivity, durability, energy efficiency, environmental sustainability, and immediate worker safety. However, there is limited knowledge about the ergonomics of these machines, as negative ergonomic aspects often accumulate over time and become apparent much later, in contrast to more immediate features. Featured studies imply ergonomic inferiority of skidders in comparison to other extraction machinery. The aim of this study was to conduct a comprehensive assessment of the ergonomic features of skidders manufactured by the Croatian company Hittner Ltd, and to propose possible solutions for their improvement. For this task, ergonomic guidelines (checklist) for forest machines, established by several European countries, were used. Skidders Ecotrac 60V and 140V were assessed at the Hittner Ltd. facility. Results show significant drawbacks in Cab access, Working posture, and Winch sections. Workstation levelling, better seat, thicker steel rope, and a hydraulic spool-out device were offered as major potential means of improving ergonomics.

Evaluating an Electric Battery for Energy Storage in a Parallel Hybrid Thinning Harvester

volume: 48, issue: 1

This research assesses the feasibility of employing an electric battery as an energy storage medium in the parallel hybrid powertrain of a thinning harvester, proposing it as a more economical substitute for traditional supercapacitors. An AH6 thinning harvester incorporating a battery-hybrid system was observed during felling tasks across three combustion engine speeds: 1700 rpm, 1800 rpm, and 1900 rpm. These three modes were selected in an effort to get as close as possible to the optimal RPM of 1500. Battery energy accumulation rose by 0.06 kWh at both 1700 rpm and 1800 rpm; in contrast, it declined by 0.002 kWh at 1900 rpm. Multi-criteria evaluation of felling regimes substantiated the electric battery viability as an energy storage option for thinning harvesters. Peak efficacy emerged at reduced engine speeds, coinciding with the maximum torque output of the combustion engine. These outcomes bear substantial relevance for curbing emissions and operational expenses in thinning forestry practices.

Forestry Machinery Ergonomic Assessment: A Case Study on Ecotrac Cable Skidders

volume: 48, issue: 1

Skidders used in forest operations are regarded as specialized machines optimized for effective and safe wood skidding across rugged terrain. Their dimensions, design, and various technical attributes are primarily influenced by practical considerations, such as productivity, durability, energy efficiency, environmental sustainability, and immediate worker safety. However, there is limited knowledge about the ergonomics of these machines, as negative ergonomic aspects often accumulate over time and become apparent much later, in contrast to more immediate features. Featured studies imply ergonomic inferiority of skidders in comparison to other extraction machinery. The aim of this study was to conduct a comprehensive assessment of the ergonomic features of skidders manufactured by the Croatian company Hittner Ltd, and to propose possible solutions for their improvement. For this task, ergonomic guidelines (checklist) for forest machines, established by several European countries, were used. Skidders Ecotrac 60V and 140V were assessed at the Hittner Ltd. facility. Results show significant drawbacks in Cab access, Working posture, and Winch sections. Workstation levelling, better seat, thicker steel rope, and a hydraulic spool-out device were offered as major potential means of improving ergonomics.